PAGE 1
C 16060 - 1 en 0906 / ANKO 1 (37) MERCEDES BENZ ENGINE FAULT CODES E 2006 SANDVIK TAMROCK CORP., Tampere Plant P.O. Box 100 FI--33311 TAMPERE, Finland Tel.
PAGE 2
(37) C 16060 - 1 en 0906 / ANKO MERCEDES BENZ ENGINE FAULT CODES E 2006 SANDVIK TAMROCK CORP., Tampere Plant P.O. Box 100 FI--33311 TAMPERE, Finland Tel.
PAGE 3
C 16060 - 1 en 0906 / ANKO 3 (37) MERCEDES BENZ ENGINE FAULT CODES 1.1. Fault codes of engine control (PLD--MR) via SAE J1939 Fault-codes. SAE J1939 SPN/FMI **** 45/12 Fault-codes. PLD-MR *** Description 16409D) heater flange Repair instructions open circuitfault (heater flange defective) The heating flange becomes after Kl. 15 uniquely briefly switched on. Here if no break-down of the battery voltage is recognized, the heating flange is classified as defective.
PAGE 4
C 16060 - 1 en 0906 / ANKO 4 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 02517 oil level sensor (up to diagnosis version 4) measured value not plausible -- check oil level, correct if necessary. -- check wire for short circuit to battery, repair or replace if necessary. -- check oil level sensor, replace if necessary. nominal value: 20--25 Ohm -- perform functional check.
PAGE 5
C 16060 - 1 en 0906 / ANKO 5 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 100/2 11617 oil pressure sensor signal not plau- -- check oil level, correct if nesible cessary. -- check wire for open circuit fault, repair or replace if necessary. -- check oil pressure sensor, replace if necessary. -- perform functional check.
PAGE 6
C 16060 - 1 en 0906 / ANKO 6 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 102/2 11417 boost pressure sensor measured value not plausible -- check wire for open circuit fault, repair if necessary. -- check boost pressure sensor, replace if necessary. -- perform functional check. -- if fault code 01315 or 01316 also actual: replace and calibrate ECU engine control (e.g. MR--PLD).
PAGE 7
C 16060 - 1 en 0906 / ANKO 7 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 102/13 12415 scavenging (boost pres-- check sensor, replace if necgradient sensor sure ) measuressary. (P2S--P3)** ing range ex-- check wire for open circuit ceeded 102/13 12416 scavenging (boost pres-- check sensor, replace if necgradient sensor sure ) remains essary.
PAGE 8
C 16060 - 1 en 0906 / ANKO 8 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 110/3 11515 coolant temperature sensor measuring range exceeded -- check sensor, repair or replace if necessary. -- nominal value: 2.4 kOhm (corresponds to 21°C) -- check wire for open circuit fault or if shortened to battery voltage, repair if necessary. -- perform functional check.
PAGE 9
C 16060 - 1 en 0906 / ANKO 9 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 168/4 07543 terminal 30, battery voltage remains below nominal range -- 24 V--Mode: 22 V, 12 V-Mode: 10 V -- battery defect -- alternator, governor or fuse defect 174/3 11115 fuel temperature sensor measuring range exceeded -- check wire, repair or replace if necessary. -- nominal value: 2.4 kOhm (corresponds to 21°C).
PAGE 10
C 16060 - 1 en 0906 / ANKO 10 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 190/0 10530 engine speed engine speed too high -- inform about authorized engine speed -- delete fault memory 609/11 04056 internal fault* backup control -- check all affected connectors, defective* plug connections and electrical components for damage, loose contact, corrosion etc. and repair if necessary.
PAGE 11
C 16060 - 1 en 0906 / ANKO 11 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** 609/12 Fault-codes. PLD-MR *** 04024 Description internal fault Repair instructions auxiliary con-- check all affected connectors, troller defective plug connections and electrical components for damage, loose contact, corrosion etc. and repair if necessary. -- if fault code is still present, renew and program control unit. -- perform functional check.
PAGE 12
C 16060 - 1 en 0906 / ANKO 12 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 609/12 14039 internal fault* 14039 starter -- check all affected plugs, plug driver low--reconnectors and electrical sistance (main components for damage, path or auxilialoose contact, corrosion etc. ry path) and repair if necessary.
PAGE 13
C 16060 - 1 en 0906 / ANKO 13 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** 609/12 Fault-codes. PLD-MR *** 18039 Description internal fault** Repair instructions Starter output stage with low impedance (main branch or branch of emergency) or load (relay) also to high resistance and/or to high inductance. Main branch: During the controller initialization the two transistors of the main branch are alternating switched on briefly.
PAGE 14
C 16060 - 1 en 0906 / ANKO 14 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 609/14 04048 internal fault cylinder num- -- check all affected connectors, ber implausible plug connections and electrical components for damage, loose contact, corrosion etc. and repair if necessary. -- --perform functional check.
PAGE 15
C 16060 - 1 en 0906 / ANKO 15 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 609/14 24053 internal fault ** EEPROM: Checksum-fault 3 (block production or immobilizer). -- check all affected connectors, plug connections and electric components for damage, loose contact, corrosion etc., and repair if necessary. -- if fault code still present, renew and calibrate control unit. -- --perform functional check .
PAGE 16
C 16060 - 1 en 0906 / ANKO 16 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 625/14 10100 CAN connection CAN--High de- -- check for open circuit fault, refective pair or replace if necessary. -- switch on ignition. -- delete fault memory in ECU engine control (e.g. MR--PLD). -- delete fault memory in SG FRE. -- --perform functional check .
PAGE 17
C 16060 - 1 en 0906 / ANKO 17 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 636/3 10309 crankshaft position crankshaft sen- -- check wire and position sensor open circuit sor for open circuit fault, refault place if necessary. -- --nominal value 1.2 kOhm. 636/4 10308 crankshaft position crankshaft sen- -- check wire and position sensor ground sor for ground short, replace if necessary. -- --nominal value 1.
PAGE 18
C 16060 - 1 en 0906 / ANKO 18 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 636/14 10313 crankshaft position crankshaft sen- -- connect the position sensor sor wrong pocorrectly. larity -- --perform functional check.
PAGE 19
C 16060 - 1 en 0906 / ANKO 19 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 651/7 15026 contact recog- no contact cylimportant note: nition injector--/ inder 1 -- upon removing mechanical or solenoid valve electrical faults at the injector valves, the engine smoothness control has to be set to zero.
PAGE 20
C 16060 - 1 en 0906 / ANKO 20 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 652/7 15126 contact recog- no contact cyl- -- upon removing mechanical or nition injector--/ inder 2 electrical faults at the injector solenoid valve valves, the engine--smoothcylinder 2 ness control has to be set to zero.
PAGE 21
C 16060 - 1 en 0906 / ANKO 21 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 653/7 15226 injector--/solenoid valve cylinder 3 contact recognition injector--/solenoid valve: no contact cylinder 3 important note: -- upon removing mechanical or electrical faults at the injector valves, the engine smoothness control has to be set to zero.
PAGE 22
C 16060 - 1 en 0906 / ANKO 22 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 654/12 09344 injector--/solenoid valve cylinder 4 engine-important note: smoothness -- upon removing mechanical or control: LRR-electrical faults at the injector limitation cylinvalves, the engine smoothder 4 ness control has to be set to zero.
PAGE 23
C 16060 - 1 en 0906 / ANKO 23 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 655/14 09445 injector--/solenoid valve cylinder 5 individual cylin- important note: der adaptation: -- upon removing mechanical or EZA--limitation electrical faults at the injector cylinder 5 valves, the engine smoothness control has to be set to zero.
PAGE 24
C 16060 - 1 en 0906 / ANKO 24 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 657/5 15627 injector--/solenoid valve cylinder 7 control failure injector--/solenoid valve important note: -- upon removing mechanical or electrical faults at the injector valves, the engine smoothness control has to be set to zero.
PAGE 25
C 16060 - 1 en 0906 / ANKO 25 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 658/6 25728 injector--/solenoid valve cylinder 8** short circuit in- -- check electrical screw conjector--/ solenections of the affected injecnoid valve cyltor valve for short circuit. inder 8 -- disconnect electrical screw connections of the affected injector valve.
PAGE 26
C 16060 - 1 en 0906 / ANKO 26 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 677/5 18009 starter control (PLD--MR)** starter relay external current supply -- check of starter relay if shortened to battery voltage, repair or replace if necessary. -- check starter relay, replace if necessary.
PAGE 27
C 16060 - 1 en 0906 / ANKO 27 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes. PLD-MR *** Description Repair instructions 697/5 17009 proportional open circuit -- check parametrization. valve 1 (MBR-- fault** ECU en- -- parameter 06 has to be set to BK) gine control NOT ACTIVE (e.g. MR--PLD) wrong calibra- -- if not, then the data set of ECU engine control (e.g. MR--PLD) tion. is wrong -- replace and program ECU engine control (e.g. MR--PLD).
PAGE 28
C 16060 - 1 en 0906 / ANKO 28 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** 699/3 699/5 Fault-codes. PLD-MR *** Description 17107D) proportional valve 3 17109 proportional valve 3 Repair instructions shortened to -- set output off battery voltage (--lead)* open circuit -- check calibration, correct if fault wrong calnecessary. Parameter 008 ibration has to be set to NOT ACTIVE.
PAGE 29
C 16060 - 1 en 0906 / ANKO 29 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** 700/5 Fault-codes. PLD-MR *** 17209 Description proportional valve 4 open circuit fault Repair instructions note: ECU engine control (e.g. MR--PLD) wrong calibration / open circuit fault -- check calibration, correct if necessary. Parameter 009 has to be set to NOT ACTIVE. note: -- if a Linnig--fan is installed, the following calibration applies: a) parameters 8 and 9 have to be set to ACTIVE.
PAGE 30
C 16060 - 1 en 0906 / ANKO 30 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** 700/6 Fault-codes. PLD-MR *** 17206 Description proportional valve 4 Repair instructions short circuit to ground (--lead) -- -- -- -- note: ECU engine control (e.g. MR--PLD) wrong calibration / short circuit to ground check calibration, correct if necessary. Parameter 009 has to be set to NOT ACTIVE. check calibration, correct if necessary. Parameter 009 has to be set to NOT ACTIVE.
PAGE 31
C 16060 - 1 en 0906 / ANKO 31 (37) MERCEDES BENZ ENGINE FAULT CODES Fault-codes. SAE J1939 SPN/FMI **** Fault-codes.
PAGE 32
C 16060 - 1 en 0906 / ANKO 32 (37) MERCEDES BENZ ENGINE FAULT CODES 1.2.
PAGE 33
C 16060 - 1 en 0906 / ANKO 33 (37) MERCEDES BENZ ENGINE FAULT CODES ADM2 ADM2 fault fault codes codes (J1939) (k-SPN/FMI line) **** *** Description Remedial action Pin 91/3 10203 analog accelerator pedal voltage too high or shorted to battery voltage -- Pedal unit exchange, if defective -- check wiring -- Limit value idle operation position: 5,0 V -- Limit value kickdown position: 4,9 V 21/11 91/4 10204 analog accelerator pedal AFPS voltage too low or shorted to ground -- Pedal unit exchange,
PAGE 34
C 16060 - 1 en 0906 / ANKO 34 (37) MERCEDES BENZ ENGINE FAULT CODES ADM2 ADM2 fault fault codes codes (J1939) (k-SPN/FMI line) **** *** Description Remedial action Pin 107/4 10804 air filter sensor shorted to ground -- check wiring. 15/08 110/0 10900 coolant temperature high coolant temperature -- cooling--water level and cooling circuit check. PLD-MR 110/14 10914 coolant temperature coolant temperature too high -- cooling--water level and cooling circuit check.
PAGE 35
C 16060 - 1 en 0906 / ANKO 35 (37) MERCEDES BENZ ENGINE FAULT CODES ADM2 ADM2 fault fault codes codes (J1939) (k-SPN/FMI line) **** *** Description Remedial action Pin 599/12 11812 cruise control both switches -- check wiring switch closed -- check cruise control switch CC+ and CC-- 18/04 and 18/05 601/12 11912 cruise control both switches -- check wiring switch closed -- check cruise control switch CC+ and CC-- 18/04 and 18/05 620/3 12103 power supply analog pedal (AFP+) voltage too high --
PAGE 36
C 16060 - 1 en 0906 / ANKO 36 (37) MERCEDES BENZ ENGINE FAULT CODES ADM2 ADM2 fault fault codes codes (J1939) (k-SPN/FMI line) **** *** Description Remedial action Pin 730/1 13901 output relay 2 grid heater: -- check wiring relay perma- -- check relay 2 nently closed 15/09 730/2 13902 output relay 2 grid heater: -- check wiring relay perma- -- check relay 2 nently closed 15/09 730/3 13903 output relay 2 voltage too high or shorted to battery voltage 15/09 730/4 13904 output relay 2 voltage t
PAGE 37
C 16060 - 1 en 0906 / ANKO 37 (37) MERCEDES BENZ ENGINE FAULT CODES ADM2 ADM2 fault fault codes codes (J1939) (k-SPN/FMI line) **** *** Description Remedial action Pin 1006/3 14603 exhaust brake open circuit valve MBR_BK -- check wiring -- check exhaust brake valve 15/06 1006/4 14604 exhaust brake shorted to valve ground MBR_BK -- check wiring -- check exhaust brake valve 15/06 639/2 14902 J1939 CAN-interface 1015/1 15001 PWM acceler- no supply ator pedal voltage -- check wiring 1015/2 1